【正品现货】CROWN 皇冠 XTi1000 专业功放 ◆ 产品描述: 特点: * 内置分频、均衡、限幅、延时和次谐波合成器等数字处理能力 * 可通过LCD显示屏,直接调较扬声器预置参数 * 准确、低失真及无染色的音质 * 先进及周密的电路保护设计,可确保短路、开路、直流电冲击,误区匹配,机器温度过热,高频信号过载及内 部元器件损坏等鼓掌 * 满足各种类型负载阻抗及模式连接,如:2Ω,4Ω和8Ω阻抗,立体声/单声道桥接输出连接 * 安全可靠的开关电源供电 * 轻巧及坚固的外型、各款功放净重只有7.7公斤和2U高度标准机箱体积 * 方便及易接插件,设有SPEAKON插座和接线柱端子输出件,XLR卡农输入接头及扬声器并联接件 * 每个通道的“状态”都能在LCD显示屏清晰监控
◆ 产品配置: 型号:XTi1000 立体声输出:2Ω:700W 4Ω:500W 8Ω:275W 单声道(桥接)输出功率:4Ω :1400W 8Ω:1000W 型号:XTi2000 立体声输出:2Ω:1000W 4Ω:800W 8Ω:475W 单声道(桥接)输出功率:4Ω :2000W 8Ω:1600W 型号:XTi4000 立体声输出:2Ω:1600W 4Ω: 1200W 8Ω:650W 单声道(桥接)输出功率:4Ω :3200W 8Ω:2400W 型号:XTi6000 立体声输出:2Ω:3000W 4Ω:2100W 8Ω:1200W 单声道(桥接)输出功率:4Ω 6000W 8Ω:4200W 电压增益: 在1kHz、8Ω额定负载输出时,额定 XTi1000为35.5dB, XTi2000为32.9dB, XTi4000为34.2dB XTi 6000: 37.1dB. 频率响应: 20Hz-20 kHz ±0.25dB(1w/4Ω负载) 相们响应: 满足各种类型负载,立体声模式的负载范围为2-8Ω,单声道桥接的负载范围为4-8Ω 输入灵敏度: 1.4V 信号噪声比: A计权105dB(低于1 kHz额定输出功率, 8Ω负载) 阻尼系数: >500(20Hz-500Hz) 通道间串音: >80dB (20Hz- 1kHz,额定输出功率) 共模抑制比(CMR): >45dB (20Hz- 1kHz) 输入级: 电子平衡输入,采用1%精度的电阻器 最大输入信号: +22dBu,典型值 交流电源电压和频率:100V、120V、220V-240V,50Hz- 60Hz 交流电源电流: XTi1000:6.5A, XTi2000:6.9A, XTi4000:8.0A,XTi 6000: 15.3A 空载消耗不大于: 90w 工作环境温度: 0℃-40℃,95%相对湿度(无凝露) DSP数字信号处理部分 均衡器EQ: 每通道有一个4段参数均衡器, ±12dB提升衰减,还可以调整滤波器两边的斜率
滤波器: 每通道有一个高通和低通滤波器,每个倍频程的斜率为1/6,1/12,1/18,1/24,Butherworth型 延时装置: 作为驱动器的信号调整,总延时为50ms 次谐波合成器: 增加低频能量 输出限幅器: 防止功率输出信号削波 预置: 10个扬声器预置 前面板控制和显示器 电平控制: 每通道一个旋转音量控制器 电平开关: 控制功放电源 Sec/Prev/Next按钮:靠近LCD显示屏的三个按钮用于存取菜单及选择项目 LCD显示屏: 液晶体显示,显示扬声器预置 信号指示器: 每通道一个绿色LED,输入端信号电平非常低时或LED闪亮时立即须要检查连接电缆及其它故障 -10dB指示器: 输出信号超过信号削波电平之下-10dB时,绿色LED闪亮 -20dB指示器: 输出信号超过信号削波电平之下-20dB时,绿色LED闪亮 准备指示器: 功放运行准备完成后,每个通道一个绿色LED点亮 削波指示器: 每个通道的一个红色信号超载输出时,LED点亮可闻失真的门限值时 过热/故障指示器: 机器过热或发生故障时,每个通道的一个红色LED点亮 后面板控制和连接器 交流电电源连接器: NEMA5-15P(15A) 输入连接器: 每通道一个 XLR插座 并联/输出连接器: 每通道一个从输出连接器到其它功放的输入 输出连接器: 2个Neutrik Speakon NL4MP扬声器输出连接器(NL4FC为公插座),1个扬声器插座用于连接通道1和通道2输出,采用单根4芯电缆,还有2个接线柱输出端子(与扬声器插座并联连接) HiQnet USB连接器: B型,连接HiQnet 网络 保护 XTi系列功放设有负载短路保护、负载开路保护、误区匹配保护、电 源过载(过压)保护、机器温度过热保护、链路损坏保护、输入电流 过载保护、防RF射频窜音保护等有效的各种保护措施。还有保护扬 声器装置的防止直流输入/输出、防止直流偏置输出的电源开/关的瞬 间冲击保护等 Power Amplifier (1400 Watts) Integrated proprietary DSP. Accurate, uncolored sound. Advanced protection circuitry. Switch-mode universal power supply. The XTi Series of Crown amplifiers are professional tools designed and built for portable PA applications. The series includes 3 models which are identical except for output power: XTI 1000, 2000 and 4000. All are rugged and lightweight, and offer unmatched value in their class. XTi-Series amplifiers feature an LCD screen with DSP speaker presets for crossover frequencies, EQ, limiting, delay, and a subharmonic synthesizer. Other features include a switch-mode universal power supply, useful function indicators, proportional-speed fan assisted cooling, XLR inputs, Speakon and binding-post outputs, short-circuit protection and more. With their powerful, reliable performance, XTi-Series amps easily handle 2-Ω loads and are capable of chest-thumping lows. Plus, your investment in an XTI-Series amplifier is backed by Crown's 3-Year, No-Fault, Fully Transferable Warranty. Features: Integrated proprietary DSP with LCD front panel display Accurate, uncolored sound with very low distortion for the best in music and voice reproduction Advanced protection circuitry guards against: shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults Extremely versatile, handling a wide range of speaker impedances and outputs Switch-mode universal power supply Speaker presets for crossover frequencies, EQ, limiting, and delay All products fill 2U rack spaces and weigh under 17 lbs.; weight sets a new standard in lightweight amps (20% less) Speakon and binding post outputs, XLR inputs and loop-thrus Comprehensive LED status per channel 3-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications Technical Info XTi 1000 Power: 8 Ω: 275W 4 Ω: 500W 2 Ω: 700W* 8 Ω bridged to mono: 1000W 4 Ω bridged to mono: 1400W* ·With 1% THD. Voltage Gain at 1kHz, 8 Ω rated output: XTi 1000: 30.5 dB XTi 2000: 32.9 dB XTi 4000: 34.2 dB Frequency Response: +/-0.25 dB from 20 Hz to 20 kHz at 1 watt into 4 Ω Phase Response (at 1 watt, 20 Hz to 20 kHz): +/-15 degrees Load Impedance: Safe with all types of loads. Rated for 2 to 8 Ω in Stereo mode, 4 to 16 Ω in Bridge-Mono mode Sensitivity: 1.4V Signal to Noise Ratio (below rated 1 kHz power at 8 Ω): 105 dB (A weighted) Damping Factor: Better than 500 from 20 Hz to 500 Hz Crosstalk: > 80 dB below rated power, 20 Hz to 1 kHz Common Mode Rejection (CMR): > 45 dB from 20 Hz to 1 kHz Input Stage: Input is electronically balanced and employs precision 1% resistors Input Impedance (nominal): 20 k Ω, balanced;10 k Ω, unbalanced Maximum Input Signal: +22 dBu typical AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V 50/60 Hz AC Line Current: XTi 1000: 6.5A XTi 2000: 6.9A XTi 4000: 8.0A At Idle: Draws no more than 90 watts Operating Temperature: 0 degrees C to 40 degrees C at 95% relative humidity (non-condensing) DSP Section EQ: 4-band paragraphic per channel, boost/cut 3354665saasdasdLiangyu00671089429 3354665saasdasdLiangyu00671089429
|